Members
Total Members: 116
Latest: broncogirl2021 New This Month: 0 New This Week: 0 New Today: 0
Stats
Total Posts: 2922
Total Topics: 389
Most Online Today: 7
Most Online Ever: 24
(June 12, 2013, 04:55:11 PM)
Users Online Members: 0 Guests: 5 Total: 5
|
|
Pages: 1 ... 5 6 [7] 8 9 10
61
« Last post by K9KITT on July 25, 2017, 08:59:34 PM »
Want to start doing some upgrades to my 75 bronco. I haven't done much to it in the past couple of years and I'm ready to start doing some upgrades. I'm thinking about starting with a hydroboost power brake system. Right now it has power front disk brakes and drums in the back. Anyone know who might could install this and is it a good thing to start with or should I start with upgrading the steering which is another thing I want to upgrade?
62
I changed because the emulsion tubes on my 2100 split and caused it to have a bad hesitation. Then I bought a new aftermarket 2100 clone and it ran like crap. This was my third choice but I had the parts already and it gets me closer to Fitech efi if this doesn’t work out.
63
« Last post by lonesouth on July 21, 2017, 11:13:46 AM »
that's a clean engine bay why the change?
64
If any of you are running the GM based 1 ton steering on your Broncos you should look into "the Cure" by Ruff Stuff Specialties. The steering felt a little loose after I installed the 1 Ton steering but it wasn't loose, It just rolls the tie rod a little when you turn back and forth. After installing the Cure spacer/bushing the roll is gone and the steering feels much better. http://www.ruffstuffspecialties.com/catalog/R1768.html
65
Got the new intake and carb installed last week. Had a little issue with some trash in the carb but got it cleaned out and running good now.
It's a 85 Mustang factory aluminum 4bbl manifold, Holley heat shield, 1 inch plastic spacer, and a 600cfm Holley carb.
67
« Last post by lonesouth on May 18, 2017, 01:22:27 PM »
$455 to my door.
68
Can't wait to see how it turn out, I need to upgrade to a larger tank one day.
How much did the Aero cost including shipping?
69
« Last post by lonesouth on May 17, 2017, 09:27:15 AM »
I bought this thing over a year ago on a group buy from classicbroncos. It sat in the corner of my garage since then. Finally got around to unwrapping it about a month ago. Spent an hour, got the sender dialed in, then it sat for another month on my workbench. Last week, I got it mocked up in place and welded on the mounting brackets. All set to install it, and the filler neck is 1.75", stock is 2". AHHHHHH. Ordered a new filler hose from Jeffs, should have been here monday, USPS has sent it on a tour of the gulf states. Ready to be done and move on to the next project.
70
« Last post by JustaFordGuy on April 17, 2017, 08:26:21 AM »
Isn't it nice to have an easy to fix problem for a change.
Pages: 1 ... 5 6 [7] 8 9 10
|
Our 23 Bronco is finally here!!!
by JustaFordGuy
January 20, 2023, 03:00:09 PM
|
Carburetors
by broncobob
May 07, 2022, 12:36:24 PM
|
Re: Wheels and Water event Marianna Florida
by JustaFordGuy
February 06, 2020, 02:32:40 PM
|
Wheels and Water event Marianna Florida
by kat
February 05, 2020, 05:42:45 PM
|
Re: Frame off Restoration
by JustaFordGuy
November 25, 2019, 02:19:42 PM
|
Frame off Restoration
by geofw78
November 23, 2019, 06:52:04 PM
|
Dana 20 Transfer Case
by broncobob
June 10, 2019, 10:16:19 AM
|
Re: Bronco Sightings
by JustaFordGuy
April 25, 2019, 01:17:47 PM
|
|
|